- #MAC NETWORK SETTINGS STATIC IP HOW TO#
- #MAC NETWORK SETTINGS STATIC IP INSTALL#
- #MAC NETWORK SETTINGS STATIC IP FULL#
- #MAC NETWORK SETTINGS STATIC IP PC#
Modify the network settings īy default, the Pulse Streamer 8/2 will attempt to acquire an IP address via DHCP. In some cases, however, you may need to reboot your computer to detect the Pulse Streamer, if there has been a DHCP-connection before. This shall work out-of-the-box on both Windows and Linux (requires avahi/zeroconf). This address allows you to establish a connection when the Pulse Streamer is connected directly to your computer with an Ethernet cable. The Pulse Streamer is always reachable via a permanent second static IP-address 169.254.8.2 (netmask 255.255.0.0). In this example, the first line is the Pulse Streamer, and the second Use the ‘ifconfig’ command to confirm the IP address has been updated successfully.Arp Address HWtype HWaddress Flags Mask Iface 192.168.1.108 ether 00 : 26 : 32 : f0 : 09 : 30 C wlp1s0 router ether 18 : 83 : bf : c1 : 1 f : 67 C wlp1s0
#MAC NETWORK SETTINGS STATIC IP PC#
Your PC should now retain its IP address across reboots, or even when a DHCP server is not working. Sample output: $ sudo /etc/init.d/networking restart To activate the changes you will need to reboot the PC, or simply restart networking (recommended). nameserver 192.168.0.1ĭepending on your setup, this could be your router’s IP, your ISP’s DNS server IP, or a 3rd party’s DNS server, such as Google’s (8.8.8.8 and 8.8.4.4), or OpenDNS. If not, add one or more nameserver records in the format below. If one already exists, and is valid, great. You will want at least 1 nameserver set up in this file. You will also need to set up the DNS nameserver settings manually. Once you have finished with the changes to the file, save and quit the editor. The default gateway address can be obtained by using the ‘route’ command. If you are unsure what settings should go in this file, you can always run the ‘ifconfig’ command, which will output the current IP address settings obtained via DHCP.
# This file describes the network interfaces available on your system
#MAC NETWORK SETTINGS STATIC IP FULL#
iface eth0 inet staticĭepending on how many network interfaces your machine has, the output file may vary, but below is a full example of the file after being configured with a static IP. Make sure you change the relevant settings to suit your network. The # character at the beginning of the line indicates that it is commented out, and will be ignored.Īdd the following lines to set up the interface with a static IP. This allows you to change it back easily at a later date if you want to. I choose to comment it out, and add the configuration lines to set up a static IP directly below it. The line containing “iface eth0 inet dhcp” needs to either be deleted, or commented out. You should see the lines similar to the following in the editor. This guide will be using the “nano” editor. Open up the /etc/network/interfaces file in your favorite editor. The following steps will guide you through setting up your computer to use a static IP address on Ubuntu. Please see “ Setting a static IP address on Ubuntu 18.04 and higher using netplan“ for more info) ( Note: For Ubuntu 18.04 and higher, this is now done using netplan configuration.
#MAC NETWORK SETTINGS STATIC IP HOW TO#
If for whatever reason you dont want to go down the path of setting a DHCP reservation (you may not have access to the DHCP server unsure how to set it up etc), the only option is to set a static IP address on the PC itself. You could set up a IP address reservation on the DHCP server based on the hardware/mac address of the network interface, or alternativly, set the operating system to use a static IP address. There are two options for ensuring you get/use the same IP address at every boot. While that may be fine for most users, if you are wanting to set up a server, the chances are you will be wanting it to always have the same IP address.
#MAC NETWORK SETTINGS STATIC IP INSTALL#
During a default install of Ubuntu it will try and automatically obtain an IP address using DHCP.